|
|
|
| Online Store |
|
Do-It-Yourselfers:
For crack repairs, you will need approximately 1 lb. of Xypex® Concentrate
and 1 lb. of Xypex® Patch'n Plug for every linear foot of crack.
For surface applications, you will need approximately 1 lb. of Xypex® Concentrate
for every six square feet.
Click here for application instructions.
NOTE: products from this site are available only to the Intermountain West area, in the following states:
Colorado, Idaho, Montana, New Mexico, Utah, and Wyoming.
 |
|
| Xypex Concentrate - 60lb pail |
| Xypex Concentrate is the most chemically active product within the Xypex Crystalline Waterproofing System. When mixed with water, this light grey powder is applied as a cementitious slurry coat to above-grade or below-grade concrete, either as a single coat or as the first of a two-coat application. It is also mixed in Dry-Pac form for sealing strips at construction joints, or for the repairing of cracks, faulty construction joints and honeycombs. Xypex prevents the penetration of water and other liquids from any direction by causing a catalytic reaction that produces a non-soluble crystalline formation within the pores and capillary tracts of concrete and cement-based materials. |
| Click here for PDF product data sheet |
|
|
|
 |
|
|
 |
|
| Xypex Modified - 60lb pail |
| Xypex Modified can be applied as a second coat to reinforce Xypex Concentrate, or applied by itself to dampproof the exterior of foundation walls. Applied as a second coat, Xypex Modified chemically reinforces Xypex Concentrate where two coats are required and produces a harder finish. Where dampproofing is required, a single coat of Modified may be used as an alternative to a spray/tar emulsion. Xypex prevents the penetration of water and other liquids from any direction by causing a catalytic reaction that produces a non-soluble crystalline formation within the pores and capillary tracts of concrete and cement-based materials. |
| Click here for PDF product data sheet |
|
|
|
 |
|
| Xypex Patch 'n Plug - 60lb pail |
| Xypex Patch'n Plug is a specially designed, fast-setting, non-shrink, high-bond-strength, hydraulic cement compound for concrete patching and repair. Patch'n Plug stops flowing water in seconds and is used to seal cracks, tie holes, and other defects in concrete. The high performance characteristics of Patch'n Plug are enhanced by Xypex's unique crystalline waterproofing technology. |
| Click here for PDF product data sheet |
|
|
|
 |
|
|
 |
|
| Xypex Megamix I - 60lb pail |
| Xypex Megamix I is a thin parge coat for the waterproofing and resurfacing of vertical masonry or concrete surfaces, as a cap coat for Xypex Concentrate, or as an architectural rendering. Megamix I is a unique blend of portland cement, treated silica sand, fibers and proprietary chemicals. It is mixed with Xycrylic Admix to produce enhanced bond. Megamix I is applied by brush or trowel up to a thickness of 3/8" (10 mm). The high performance characteristic of Megamix I are enhanced by Xypex's unique crystalline waterproofing and protection technology. |
| Click here for PDF product data sheet |
|
|
|
 |
|
| Xypex Megamix II - 60lb pail |
| Xypex Megamix II is a thick repair mortar for the patching and resurfacing of deteriorated concrete. Megamix II has been specifically formulated to produce superior bond, low shrinkage, chemical durability and high strength. It is a one component mortar and can be either sprayed or trowel applied at a thickness of 3/8" to 2" (10 mm to 50 mm). The high performance characteristics of Megamix II are enhanced by Xypex's unique crystalline waterproofing and protection technology. |
| Click here for PDF product data sheet |
|
|
|
 |
|
| Xypex FCM 40 |
| Xypex FCM 40 is specifically designed for repairing cracks subject to movement, sealing construction joints, restoring deteriorated concrete, and waterproofing concrete structures. FCM 40 has exceptional adhesive and elongation characteristics and is often used in conjunction with the Xypex Crystalline Concrete Waterproofing and Protection System. FCM is a two component product consisting of a specialized liquid polymer dispersion and a cementitious powder. These ingredients are mixed just prior to application. FCM 40 is used under normal environmental conditions, where the lowest annual ambient temperature is not below 5 |
| Click here for PDF product data sheet |
|
|
|
|
|
| Xypex FCM 60 |
| Xypex FCM 60 is specifically designed for repairing cracks subject to movement, sealing construction joints, restoring deteriorated concrete, and waterproofing concrete structures. FCM 60 has exceptional adhesive and elongation characteristics and is often used in conjunction with the Xypex Crystalline Concrete Waterproofing and Protection System. FCM is a two component product consisting of a specialized liquid polymer dispersion and a cementitious powder. These ingredients are mixed just prior to application. FCM 60 is formulated for environments subject to very low temperatures (to -40 |
| Click here for PDF product data sheet |
|
|
|
 |
|
| Xypex Gamma Cure - 1 gal |
| Xypex Gamma Cure is a curing agent designed specifically for Xypex crystalline waterproofing products. Gamma Cure may be used as an alternative to water curing for certain Xypex applications. It is also used to accelerate the Xypex Crystallization Process. Xypex Gamma Cure acts as an evaporation retardant by retaining the maximum amount of moisture in the Xypex coating. It also provides a catalyst for the reaction with the Xypex crystalline waterproofing treatment. It is a self-disappating (2-3 days) non-film forming product. |
| Click here for PDF product data sheet |
|
|
|
 |
|
| Concrete Brush 4" (10cm) |
| This 4" (10cm) Xypex-designed brush is for vertical applications. Bristles are made of chemically resistant PVC material and have flagged tips to retain the slurry material during applications. |
|
|
|
|
|
| Concrete Brush 6" (15cm) |
| This is the same Xypex-designed brush, in a 6" (15cm) size. |
|
|
|
 |
|
| Leather Gloves |
| Durable leather for use during heavy work; for example, when using power tools such as chipping and packing hammers. We recommend a reinforced palm patch for extra wearability. |
|
|
|
 |
|
| Rubber Gloves |
| Provide protection for hands and forearms during Xypex applications. They are chemical resistant and have embossed palms for wet handling. |
|
|
|
PRODUCTS FROM THIS SITE ARE AVAILABLE ONLY TO THE INTERMOUNTAIN WEST AREA, IN THE FOLLOWING STATES:
COLORADO, IDAHO, MONTANA, NEW MEXICO, UTAH, AND WYOMING.
|
